Italian ATOS hydraulic cylinder CK-32/22*0192-C301 in stock

Brand

ATOS/Italian Atos

Application Areas

Environmental Protection, Chemical Industry, Petroleum, Mining, Energy

ATOS Vane Pumps, ATOS Hydraulic Cylinders, ATOS Relief Valves, ATOS Proportional Valves, ATOS Stack Valves, ATOS Solenoid Valves

Features of Italian ATOS Hydraulic Cylinders:

1. Since pneumatic systems generally operate at pressures between 0.2-1.0 MPa, pneumatic cylinders cannot be used as high-power power components in hydraulic cylinders. Hydraulic cylinders, however, can be used as higher-power components or in hydraulic cylinder systems.

2. Air is an inexhaustible medium, eliminating cost and supply difficulties. Used air can be directly discharged into the atmosphere, making disposal convenient and preventing hydraulic oil contamination.

3. Air has low viscosity, resulting in less resistance than hydraulic oil.

4. However, because air has a much higher compressibility than hydraulic oil, its operational smoothness and responsiveness are significantly inferior.

The machining of ATOS hydraulic cylinders from Italy: As a key component in hydraulic cylinders, mining single-pillar supports, hydraulic supports, and gun barrels, the quality of the cylinder's machining directly affects the lifespan and reliability of the entire product. Cylinder machining requires high precision, with an internal surface roughness requirement of Ra 0.4–0.8µm, and strict requirements for coaxiality and wear resistance. A fundamental characteristic of cylinders is deep-hole machining, which has always been a challenge for machining personnel. Roller burnishing, by leaving residual compressive stress on the surface layer, helps to close micro-cracks and hinders the propagation of corrosion. This improves surface corrosion resistance and delays the initiation or propagation of fatigue cracks, thus increasing the cylinder's fatigue strength. Through roller burnishing, a work-hardened layer is formed on the roller-burnished surface of ATOS hydraulic cylinders, reducing the elastic and plastic deformation of the contact surfaces of the grinding pairs, thereby improving the wear resistance of the cylinder's inner wall and preventing burns caused by grinding. The reduced surface roughness after roller burnishing improves the fit.

Regarding hydraulic systems, ATOS hydraulic cylinders from Italy require specific steps within the system. Positioning components must be configured at the piston rod end, and positioning is only possible at one end, thus losing widespread control in the hydraulic systems of various machines. This helps improve the service life of the hydraulic cylinder. Good dustproofing. When managing hydraulic cylinders, reliable sealing must be ensured, and a gas leak alarm must be installed. The input force of the hydraulic cylinder is directly proportional to the effective area of ​​the piston and its one-sided pressure difference; the hydraulic cylinder base consists of a cylinder barrel and cylinder head, piston and piston rod, sealing device, buffer device, and exhaust device. Reciprocating oscillating motion can be achieved using an oscillating hydraulic cylinder. Good dustproofing measures reduce processing difficulties; such as when the impact load compresses the piston rod. The following points must be carefully considered: Maximize the load on the piston rod of the hydraulic cylinder under tension, and ensure corrosion resistance of the steel structure. Only then can a rough and reasonable management result be achieved.

Italian ATOS hydraulic cylinder structure

Simple and reliable operation; if the piston rod is bent and cannot be connected by threads, a double piston rod hydraulic cylinder can be adopted; the management method for hydraulic cylinders is detection and diagnosis. Stable movement; reliable sealing is a necessary factor for the operation of the hydraulic cylinder. For the motion shape of the hydraulic cylinder, differential connection can be considered, or some transmission devices can be adopted to reduce the stroke. [2]

Common Models of Italian ATOS Hydraulic Cylinders:

CK-32/22*0090-P001 Hydraulic Cylinder CK-32/22*0090-P001 Hydraulic Cylinder CK-32/22*0090-P001

CK-32/22*0100-N001 Hydraulic Cylinder CK-32/22*0100-N001 Hydraulic Cylinder CK-32/22*0100-N001

CK-32/22*0120-N001 Hydraulic Cylinder CK-32/22*0120-N001 Hydraulic Cylinder CK-32/22*0120-N001

CK-32/22*0150-N001 Hydraulic Cylinder CK-32/22*0150-N001 Hydraulic Cylinder CK-32/22*0150-N001

CK-32/22*0192-C301 Hydraulic Cylinder CK-32/22*0192-C301 Oil Cylinder CK-32/22*0192-C301

CK-32/22*0200-N001 Hydraulic Cylinder CK-32/22*0200-N001 Oil Cylinder CK-32/22*0200-N001

CK-32/22*0220-N001 Hydraulic Cylinder CK-32/22*0220-N001 Oil Cylinder CK-32/22*0220-N001

CK-32/22*0250-N001 Hydraulic Cylinder CK-32/22*0250-N001 Oil Cylinder CK-32/22*0250-N001

CK-40/18*0100-D901 Hydraulic Cylinder

CK-40/18*0100-D901 Oil Cylinder

CK-40/18*0100-D901

CK-40/18*0120-X008 Hydraulic Cylinder

CK-40/18*0120-X008 Oil Cylinder

CK-40/18*0125-G908 Hydraulic Cylinder

CK-40/18*0125-G908 Oil Cylinder

CK-40/18*0140-N308 Hydraulic Cylinder

CK-40/18*0140-N308 Oil Cylinder CK-40/18*0140-N308

CK-40/18*0182-D901 Hydraulic Cylinder CK-40/18*0182-D901 Oil Cylinder CK-40/18*0182-D901

CK-40/18*0182-S601 Hydraulic Cylinder CK-40/18*0182-S601 Oil Cylinder CK-40/18*0182-S601

The company mainly deals in European and American brands. We can source brands from any European country, including leading German brands such as: BURKERT, DEMAG, HAWE, REXROTH, HYDAC, PILZ relays, FESTO, IFM sensors, E+H, HEIDENHAIN, P+F sensors, SICK, TURCK, and HIRSCHMANN industrial switches. German brands: Hengstler, Murr, Schmersal, Samson, EPRO (Emerson Group)

American brands: MOOG, ASCO, MAC, NUMATICS, PARKER, VICKERS, ROSS

British brands: Norgren

Italian brands: OMAL, ATOS, CAMOZZI, UNIVER, Camozzi