ATOS proportional valve DLHZA-T-060-V71/M in stock
$211.65
When the load is zero, if the four-way spool valve of the Italian ATOS proportional valve is open, the pressure at port p = pressure at port t + pressure loss at the valve port (ignoring other pressure losses in the oil circuit). If the pressure loss at the valve port is very small, and the pressure at port t is zero, then the pressure at port p is insufficient to supply the pilot valve to actuate the main valve spool, and the entire servo valve will fail. Therefore, the valve port of the servo valve is made relatively small, so that even when the valve port is fully open, there must be a certain pressure loss to maintain the normal operation of the pilot valve.
Brand
ATOS/Italian Atos
ATOS proportional valves are a type of proportional valve used to control flow rate and direction.
ATOS Proportional Valve Extended Information---Automatic control of electro-proportional valves can be divided into intermittent control and continuous control. Intermittent control is on-off control. Pneumatic control systems use on-off (ON-OFF) directional valves with low operating frequency to control the opening and closing of the air path. Pressure reducing valves regulate the required pressure, and throttle valves regulate the required flow rate. This traditional pneumatic control system requires multiple pressure reducing valves, throttle valves, and directional valves to achieve multiple output forces and multiple movement speeds. This not only requires more components, increases cost, and complicates the system, but also requires many components to be manually adjusted in advance. Electro-proportional valve control is a type of continuous control, characterized by the output changing with the input, and a certain proportional relationship exists between the output and input. Proportional control is divided into open-loop control and closed-loop control.
ATOS Proportional Valve Structure and Principle
When the input signal to the ATOS proportional valve increases, the pilot valve 1 of the supply solenoid valve switches, while the exhaust solenoid pilot valve 7 remains in the reset state. The supply pressure then enters the pilot chamber 5 from the SUP port through valve 1. The pilot chamber pressure rises, and this pressure acts on the diaphragm 2, opening the supply valve core 4 connected to diaphragm 2 and closing the exhaust valve core 3, generating output pressure. This output pressure is fed back to the control loop 8 via pressure sensor 6. Here, a rapid comparison and correction is performed with the target value until the output pressure is proportional to the input signal, thus demonstrating that the output pressure changes proportionally to the change in the input signal. Because there is no nozzle-baffle mechanism, the valve is insensitive to impurities and has high reliability.
ATOS Proportional Valve Features
1) Enables stepless adjustment of pressure and speed, avoiding the impact phenomenon during switching of normally open on/off valves.
2) Enables remote control and program control.
3) Compared to intermittent control, the system is simplified, and the number of components is greatly reduced. 4) Compared to hydraulic proportional valves, it is smaller, lighter, simpler in structure, and lower in cost, but its response speed is much slower than that of a hydraulic system, and it is more sensitive to load changes.
5) It uses less power, generates less heat, and produces less noise.
6) It will not cause a fire and will not pollute the environment. It is less affected by temperature changes.
ATOS proportional valves can control flow in two ways: one is on/off control: either fully open or fully closed, the flow is either at its maximum or minimum, with no intermediate state, such as ordinary solenoid direct-flow valves, solenoid directional valves, and electro-hydraulic directional valves. The other is continuous control: the valve port can be opened to any degree as needed, thereby controlling the flow rate. These valves include manually controlled ones, such as throttle valves, and electrically controlled ones, such as proportional valves and servo valves. Therefore, the purpose of using proportional valves or servo valves is to achieve flow throttling control electronically (of course, pressure control can also be achieved through structural modifications). Since it is throttling control, there will inevitably be energy loss. Servo valves differ from other valves in that their energy loss is greater because they require a certain flow rate to maintain the operation of the pre-stage control circuit.
DHZO-AE-071-S5/I
DHZO-AE-073-D5/I/10
DHZO-AE-073-S5 10
DHZO-AE-073-S5/I 10
DHZO-AT-073-P3 20
DHZO-ATE-073-P3/B/DP27SB 20
DHZO-T-051-L1
DHZO-T-051-L5 31
DHZO-T-071-D5
DHZO-T-071-L5
DHZO-T-071-S5
DHZO-TE-051-L5/Y 40
DHZO-TE-071-L5
DHZO-TE-071-S5 40/PE DHZO-TE-073-S5
DKZA-A-173-L5/PA-M/7
DKZO-A-151-S5
DKZO-A-171-L5
DKZO-A-173-S5
DKZOR-A-151-S5
DKZOR-A-151-S5/18 40
DKZOR-A-151-S5/B
DKZOR-A-153-L5/B
DKZOR-A-171-D5 40
DKZOR-A-171-L5
DKZOR-A-171-S5
DKZOR-A-171-S5/18
DKZOR-A-173-D5
DKZOR-A-173-L5 DKZOR-A-173-L5/18 40
DKZOR-A-173-L5/Y
DKZOR-A-173-S3
DKZOR-A-173-S5
DKZOR-A-173-S5/18
DKZOR-AE-171-L5 10
DKZOR-AE-171-S5
DKZOR-AE-171-S5 10/WG
DKZOR-AE-171-S5/Y 10
DKZOR-AE-173-D5 10
DKZOR-AE-173-L5 10
DKZORC-A-151-S5/18
DKZOR-T-151-L5
DKZOR-T-151-L5/Y
DKZOR-T-153-L5 DKZOR-T-171-D5
DKZOR-T-171-L5
DKZOR-T-171-S5
DKZOR-T-171-S5/Y
DKZOR-T-173-L5 40
DKZOR-TE-170-L5 40
DKZOR-TE-171-L5
DKZOR-TE-171-L5/I 40
DKZOR-TE-171-S5
DKZOR-TE-171-S5/Y The company mainly deals with European and American brands and can source brands from any European country. For example, our key German brands include: BURKERT, DEMAG, HAWE, REXROTH, HYDAC, PILZ relays, FESTO, IFM sensors, E+H, HEIDENHAIN, P+F sensors, SICK, TURCK, and HIRSCHMANN industrial switches. German brands: Hengstler, Murr, Schmersal, Samson, EPRO (Emerson Group)
American brands: MOOG, ASCO, MAC, NUMATICS, PARKER, VICKERS, ROSS
British brands: Norgren
Italian brands: OMAL, ATOS, CAMOZZI, UNIVER, Camozzi
