Italian ATOS solenoid valve SDHI-0713 available in Shanghai.

Brand

ATOS/Italian Atos

Flow Direction

Other

3C Valve Category

Industry

Application Areas

Medical & Health, Environmental Protection, Chemical Industry, Agriculture, Forestry, Animal Husbandry & Fishery, Petroleum

ATOS Solenoid Valve Faults

These faults directly affect the operation of switching and regulating valves. Common faults include the solenoid valve not operating. The following aspects should be checked:

1. Loose or detached solenoid valve wiring. The solenoid valve will not receive power. Tighten the wiring.

2. Burned-out solenoid valve coil. Disconnect the solenoid valve wiring and use a multimeter to measure. If an open circuit is found, the solenoid valve coil is burnt out. Causes include moisture in the coil, leading to poor insulation and magnetic leakage, resulting in excessive current and burnout. Therefore, prevent rainwater from entering the solenoid valve. Additionally, an overly stiff spring, excessive reaction force, or insufficient coil turns can also cause coil burnout. In an emergency, the manual button on the coil can be switched from the normal "0" position to the "1" position to open the valve.

3. Solenoid Valve Jammed: The clearance between the solenoid valve's spool sleeve and valve core is very small (less than 0.008mm), and it is usually assembled as a single piece. When mechanical impurities are introduced or there is insufficient lubrication, it can easily become jammed. A temporary fix is ​​to insert a steel wire through the small hole at the head to make it spring back. The fundamental solution is to disassemble the solenoid valve, remove the valve core and valve core sleeve, and clean them with CCI4 to ensure the valve core moves freely within the valve sleeve. During disassembly, pay attention to the assembly sequence of each component and the location of external wiring to ensure correct reassembly and wiring. Also check if the lubricator spray hole is blocked and if there is sufficient lubrication.

4. Air Leakage: Air leakage will cause insufficient air pressure, making it difficult for the forced valve to open and close. This is caused by damaged gaskets or worn spool sleeves, resulting in air leakage between several cavities. When troubleshooting solenoid valve malfunctions in switching systems, choose an appropriate time to address the issue when the solenoid valve is de-energized. If the problem cannot be resolved within one switching interval, pause the switching system and address the issue at a later time. The Italian ATOS solenoid valve contains a sealed chamber with through-holes at different positions, each connecting to a different oil pipe. Inside the chamber is a piston, flanked by two electromagnets. When the coil of one electromagnet is energized, the valve body is attracted to that side. Controlling the movement of the valve body opens or closes different drain holes. The inlet hole is always open, allowing hydraulic oil to enter different drain pipes. The oil pressure then pushes the piston in the cylinder, which in turn moves the piston rod, which in turn drives the mechanical device. Thus, controlling the flow of current to the electromagnets controls the mechanical movement.

ATOS solenoid valves are electromagnetically controlled industrial devices, fundamental components of automation systems used to control fluids. They are actuators, not limited to hydraulic or pneumatic systems. They are used in industrial control systems to adjust the direction, flow rate, speed, and other parameters of the medium. Solenoid valves can be used with different circuits to achieve the desired control, ensuring both precision and flexibility. There are many types of solenoid valves, each playing a different role in the control system. Common types include check valves, safety valves, directional control valves, and speed control valves. Commonly used ATOS solenoid valve models from Italy:

DHI-0614-X 24DC

DHI-0616/A-X 230/50/60AC

DHI-0618/A-X 24DC 23

DHI-0630/2/A-X 230/50/60AC 23

DHI-0630/2/A-X 24DC 23

DHI-0630/2-X 24DC

DHI-0631/1/2/A-X 24DC

DHI-0631/2/A-IX 24DC

DHI-0631/2/A-X 110/50/60AC 23

DHI-0631/2/A-X 230/50/60AC 23

DHI-0631/2/P-X 24DC

DHI-0631/2/WP-X 12DC 23

DHI-0631/2/WP-X 220DC 23

DHI-0631/2/WP-X 230/50/60AC

DHI-0631/2P/A-X 24DC

DHI-0631/2P-X 24DC

DHI-0631/2-X 230/50/60AC

DHI-0713-X 110/50/60AC

DHI-0713-X 230/50/60AC

DHI-0713-X 24DC

DHI-0713-X 24DC 23/PE

DHI-0714/WP-X 230/50/60AC

DHI-0714/WP-X 230/50/60AC 23/PE

DHI-0714-X 230/50/60AC

DHI-0714-X 24DC

DHI-0715/FI/NC-X 24DC

DHI-0715-X 24DC

DHI-0716-X 24DC

DHI-0717-X 24DC The company mainly deals with European and American brands and can source brands from any European country. For example, our key German brands include: BURKERT, DEMAG, HAWE, REXROTH, HYDAC, PILZ relays, FESTO, IFM sensors, E+H, HEIDENHAIN, P+F sensors, SICK, TURCK, and HIRSCHMANN industrial switches. German brands: Henstler, Murr, Schmersal, Samson, EPRO (Emerson Group)

American brands: MOOG, ASCO, MAC, NUMATICS, PARKER, VICKERS, ROSS

British brands: Norgren

Italian brands: OMAL, ATOS, CAMOZZI, UNIVER, Camostat