ATOS amplifier E-MI-AC-01F/7/RR in stock

Brand

ATOS/Italian Atos

Origin Category

Imported

Application Fields

Chemical, Petroleum, Mining, Road/Rail/Shipbuilding, Comprehensive

ATOS amplifiers are important components of transmitting devices in communication systems. Based on their operating frequency band, they are divided into narrowband high-frequency power amplifiers and wideband high-frequency power amplifiers. Narrowband high-frequency power amplifiers typically use frequency-selective circuits with frequency filtering capabilities as their output circuit, hence they are also called tuned power amplifiers or resonant power amplifiers. Wideband high-frequency power amplifiers use transmission line transformers or other wideband matching circuits as their output circuit, therefore they are also called untuned power amplifiers. A high-frequency power amplifier is an energy conversion device that converts DC energy supplied by a power source into high-frequency AC output. As known in the course "Low-Frequency Electronic Circuits," amplifiers can be classified into three classes (A, B, and C) based on their current conduction angle. Class A amplifiers have a current conduction angle of 360°, suitable for small-signal, low-power amplification. Class B amplifiers have a current conduction angle of approximately 180°; Class C amplifiers have a current conduction angle of less than 180°. Both Class B and Class C amplifiers are suitable for high-power operation. Class C amplifiers offer the highest output power and efficiency among the three operating modes. Most high-frequency power amplifiers operate in Class C. However, Class C amplifiers exhibit excessive current waveform distortion, making them unsuitable for low-frequency power amplification. They are only suitable for resonant power amplification using a tuned circuit as the load. Because the tuned circuit has filtering capabilities, the circuit current and voltage remain very close to a sine wave, resulting in minimal distortion.

ATOS amplifiers are devices that increase signal amplitude or power; they are crucial components in signal processing within automation technology tools. The amplification effect is achieved by controlling the energy source with the input signal, and the power consumption required for amplification is provided by the energy source. For linear amplifiers, the output is a reproduction and enhancement of the input signal. For nonlinear amplifiers, the output has a certain functional relationship with the input signal. Amplifiers are classified according to the physical quantities of the signals they process: mechanical amplifiers and electromechanical amplifiers.

Only signals with the same frequency as the reference signal* will produce a DC bias at the multiplier output of an ATOS amplifier; other signals will produce AC signals at the output. If a low-pass filter is added to the output of the multiplier, all AC signal components will be filtered out, leaving only the DC component whose amplitude is proportional to the amplitude of the specific frequency component in the input signal.

ATOS amplifiers are primarily used to detect weak signals with very low signal-to-noise ratios. Even if the useful signal is submerged in noise, or even if the noise signal is much stronger than the useful signal, as long as the frequency of the useful signal is known, its amplitude can be accurately measured.

ATOS amplifier

E-ME-L-01H 40/DL67SA

E-ME-L-01H 40/LQ22SA

E-ME-L-01H 40/LQ32SA

E-ME-L-01H 40/DL27SB

E-ME-L-01H 40/PCNNSA

E-ME-L-01H/DL27SB

E-ME-L-01H/I 40/LQ32SA

E-ME-T-01H 40/DH04SA

E-ME-T-01H 40/DH05SA

E-ME-T-01H 40/DK14SC

E-ME-T-01H 40/DK15SB

E-ME-T-01H 40/QV0NSA

E-ME-T-01H 40/TK14AA E-ME-T-01H 40/TK14SC

E-ME-T-01H 40/TQ25SA

E-ME-T-01H 40/TQ32SA

E-ME-T-01H 40/TQ42SA

E-ME-T-01H 40/DK14SC

E-ME-T-01H 40/DK15SB

E-ME-T-01H 40/QV1NSB

E-ME-T-01H 40/TQ25SA

E-ME-T-01H/I 40 /DH04SA

E-ME-T-01H/I 40/DK14SC

E-ME-T-01H/I 40 /DP25SB

E-ME-T-01H/I 40 /DP25SC

E-ME-T-01H/I 40 /QV0NSA

E-ME-T-01H/I 40/TQ25SA

E-ME-T-01H/I 40/DK15SB

E-ME-T-01H/I 40/QVONSA

E-ME-T-01H/I 40/TQ25SA

E-ME-T-05H 40/DH07SA

E-ME-T-05H 40/DK17SA The company mainly deals with European and American brands and can source brands from any European country. For example, our key German brands include: BURKERT, DEMAG, HAWE, REXROTH, HYDAC, PILZ relays, FESTO, IFM sensors, E+H, HEIDENHAIN, P+F sensors, SICK, TURCK, and HIRSCHMANN industrial switches. German brands: Hengstler, Murr, Schmersal, Samson, EPRO (Emerson Group)

American brands: MOOG, ASCO, MAC, NUMATICS, PARKER, VICKERS, ROSS

British brands: Norgren

Italian brands: OMAL, ATOS, CAMOZZI, UNIVER, Camozzi