ATOS proportional valve DLHZO-TEB-SN-NP-040-L03 in stock

Brand

ATOS/Italian Atos

ATOS Proportional Directional Valve Selection Criteria:

1. Selection of Proportional Directional Valve Based on Pipeline Parameters: Nominal Diameter (DN), Connection Type

1) Determine the nominal diameter (DN) based on the inner diameter of the pipeline or flow requirements on site;

2) Connection type: Generally, flange connections should be selected for DN>50, while for DN≤50, the choice can be made freely according to user needs.

2. Selection of Solenoid Valve Based on Fluid Parameters: Material, Temperature Group

1) Corrosive fluids: Corrosion-resistant proportional directional valves and all-stainless steel valves are recommended; Ultra-clean edible fluids: Food-grade stainless steel solenoid valves are recommended;

2) High-Temperature Fluids: Solenoid valves made with high-temperature resistant electrical and sealing materials should be selected, and piston-type valves should be chosen;

3) Fluid State: Valves can be gaseous, liquid, or mixed, especially for diameters greater than DN25, which must be clearly distinguished;

4) Fluid Viscosity: Generally, any choice is acceptable below 50 cSt. If this value is exceeded, a high-viscosity solenoid valve should be selected. ATOS proportional directional valves control flow in two ways:

One is on/off control: either fully open or fully closed, with flow either at its maximum or minimum, without intermediate states. Examples include ordinary solenoid direct-flow valves, solenoid directional valves, and electro-hydraulic directional valves.

The other is continuous control: the valve port can open to any degree as needed, thereby controlling the flow rate. These valves can be manually controlled, such as throttle valves, or electrically controlled, such as proportional valves and servo valves.

Therefore, the purpose of using proportional or servo valves is to achieve throttling control of flow rate electronically (of course, pressure control can also be achieved through structural modifications). Since it is throttling control, there is inevitably energy loss. Servo valves differ from other valves in that their energy loss is greater because they require a certain flow rate to maintain the operation of the pre-stage control circuit.

ATOS Proportional Directional Valve Structure and Principle

When the input signal increases, the pilot valve 1 of the supply solenoid valve switches, while the exhaust solenoid pilot valve 7 remains in the reset state. The supply pressure then enters the pilot chamber 5 from the SUP port through valve 1. The pilot chamber pressure rises, and the air pressure acts on the diaphragm 2, causing the supply valve core 4 connected to diaphragm 2 to open, while the exhaust valve core 3 closes, generating output pressure. This output pressure is fed back to the control circuit 8 via pressure sensor 6. Here, a rapid comparison and correction is performed with the target value until the output pressure is proportional to the input signal, thus demonstrating that the output pressure changes proportionally to the change in the input signal. Because there is no nozzle-baffle mechanism, the valve is insensitive to impurities and has high reliability.

ATOS Proportional Directional Valve Features

1) Enables stepless adjustment of pressure and speed, avoiding the impact phenomenon during switching of normally open on/off valves.

2) Enables remote control and program control.

3) Compared to intermittent control, the system is simplified, and the number of components is greatly reduced. 4) Compared to hydraulic proportional valves, it is smaller, lighter, simpler in structure, and lower in cost, but its response speed is much slower than that of a hydraulic system, and it is more sensitive to load changes.

5) It uses less power, generates less heat, and produces less noise.

6) It will not cause a fire and will not pollute the environment. It is less affected by temperature changes.

DKZOR-A-173-L5

DKZOR-A-173-L5/18 40

DKZOR-A-173-L5/Y

DKZOR-A-173-S3

DKZOR-A-173-S5

DKZOR-A-173-S5/18

DKZOR-AE-171-L5 10

DKZOR-AE-171-S5

DKZOR-AE-171-S5 10/WG

DKZOR-AE-171-S5/Y 10

DKZOR-AE-173-D5 10

DKZOR-AE-173-L5 10

DKZORC-A-151-S5/18

DKZOR-T-151-L5

DKZOR-T-151-L5/Y DKZOR-T-153-L5

DKZOR-T-171-D5

DKZOR-T-171-L5

DKZOR-T-171-S5

DKZOR-T-171-S5/Y

DKZOR-T-173-L5 40

DKZOR-TE-170-L5 40

DKZOR-TE-171-L5

DKZOR-TE-171-L5/I 40

DKZOR-TE-171-S5

DKZOR-TE-171-S5/Y

DKZOR-TE-173-L5 40 The company mainly deals with European and American brands and can source brands from any European country. For example, our key German brands include: BURKERT, DEMAG, HAWE, REXROTH, HYDAC, PILZ relays, FESTO, IFM sensors, E+H, HEIDENHAIN, P+F sensors, SICK, TURCK, and HIRSCHMANN industrial switches. German brands: Hengstler, Murr, Schmersal, Samson, EPRO (Emerson Group)

American brands: MOOG, ASCO, MAC, NUMATICS, PARKER, VICKERS, ROSS

British brands: Norgren

Italian brands: OMAL, ATOS, CAMOZZI, UNIVER, Camozzi