ATOS hydraulic cylinder CK-100/45*2000-N001 in stock

Brand

ATOS/Italian Atos

Application Areas

Chemical, Petroleum, Mining, Road/Rail/Marine, Comprehensive

ATOS Stack Valve, ATOS Solenoid Valve, ATOS Amplifier, ATOS Solenoid Directional Valve

Before using an ATOS hydraulic cylinder, preparations should be made. First, the hydraulic circuit should be depressurized; otherwise, when the oil pipe joints connected to the cylinder are loosened, the high-pressure oil in the circuit will quickly spray out. To depressurize the hydraulic circuit, first loosen the handwheel or pressure adjusting screw at the relief valve, etc., to unload the pressurized oil, then disconnect the power supply or power source to stop the hydraulic system.

Next, begin disassembling the hydraulic cylinder.

First, to prevent bending or deformation of slender parts such as the piston rod, use wooden blocks for even support when placing it. During disassembly, avoid damaging the piston rod tip threads, oil port threads, piston rod surface, cylinder liner inner wall, etc.

Second, disassembly should be performed in sequence. Since the structures and sizes of various hydraulic cylinders are different, the disassembly sequence will also vary slightly. Generally, the hydraulic fluid in both chambers of the cylinder should be drained before removing the cylinder head, and finally the piston and piston rod. When removing the cylinder head, special tools must be used for internal key-type connections (keys or rings); flat chisels are prohibited. For flange-type end caps, they must be pushed out with screws; hammering or prying is not allowed. If the piston and piston rod are difficult to remove, do not force them out; first determine the cause before disassembly.

Third, before and after disassembly, try to prevent the hydraulic cylinder parts from being contaminated by surrounding dust and impurities. For example, disassembly should be carried out in a clean environment; after disassembly, all parts should be covered with plastic sheeting, not cotton cloth or other work cloths.

Fourth, after disassembling the cylinder, carefully inspect it to determine which parts can continue to be used, which parts can be repaired and reused, and which parts must be replaced.

Fifth, all parts must be thoroughly cleaned before assembly.

However, it is important to ensure that all sealing devices are installed correctly. For example, when installing O-rings, do not stretch them to the point of deformation, and do not roll them in while installing; otherwise, they may become twisted and leak oil. All disassembled O-rings and dust rings should be replaced with new ones. Similarly, when installing Y-rings and V-rings, pay attention to their installation direction to avoid leaks due to incorrect installation. For Y-rings, the lip should face the pressurized oil cavity; furthermore, for YX-rings, distinguish between shaft and bore applications to avoid incorrect installation. V-rings consist of support rings, sealing rings, and pressure rings of different shapes. When the pressure ring presses against the sealing ring, the support ring causes the sealing ring to deform and achieve a sealing effect. During installation, the opening of the sealing ring should face the pressurized oil cavity; when adjusting the pressure ring, it should be tightened only to prevent leaks, avoiding excessive sealing resistance.

Sixth, a special wrench should be used when tightening threaded connections, and the torque should meet the standard requirements.

Seventh, after the piston and piston rod are assembled, their coaxiality and straightness along their entire length must be measured to ensure they do not exceed tolerances.

Eighth, after assembly, the piston assembly should move without any sense of obstruction or uneven resistance.

Ninth, when installing the hydraulic cylinder onto the main unit, a sealing ring must be added between the inlet and outlet oil ports and tightened securely to prevent leakage.

ATOS Hydraulic Cylinders:

CK-9-25/12*0190-Y301 Hydraulic Cylinder

CC-100/70*0100-S308 Hydraulic Cylinder

CE-40/18*0090-C808 Hydraulic Cylinder Hydraulic Cylinder CE-40/18*0260-X908

Hydraulic Cylinder CE-63/28*0250-C008

Hydraulic Cylinder CK/10-50/36*0250-Z601

Hydraulic Cylinder CK/10-50/36*0250-Z601

Hydraulic Cylinder CK-100/45*0370-L901 CK-100/45*0370-L901

CK-100/45*2000-N001 Hydraulic Cylinder

CK-100/45*2000-N001 Oil Cylinder

CK-100/45*2000-N001

CK-100/56*0100-P908 Hydraulic Cylinder

CK-100/56*0100-P908 Oil Cylinder

CK-100/56*0100-P908

CK-100/56*0300-L208 Hydraulic Cylinder

CK-100/56*0300-L208 Oil Cylinder

CK-100/56*0320-L208 Hydraulic Cylinder CK-100/56*0320-L208 hydraulic cylinder

CK-100/56*0320-L208 hydraulic cylinder

CK-100/56*0500-L301 hydraulic cylinder

CK-25/18*0050-N001 hydraulic cylinder

CK-25/18*0050-N001 hydraulic cylinder

CK-25/18*0055-N001 hydraulic cylinder

CK-32/14*0040-N001 hydraulic cylinder CK-32/14*0040-N001 Hydraulic Cylinder

CK-32/14*0040-N001 Hydraulic Cylinder

CK-32/14*0125-P801 Hydraulic Cylinder

CK-32/14*0140-D901 Hydraulic Cylinder

CK-32/22*0040-P001 Hydraulic Cylinder

CK-32/22*0040-P001 Hydraulic Cylinder

CK-32/22*0050-P001 Hydraulic Cylinder CK-32/22*0050-P001 hydraulic cylinder

CK-32/22*0065-N001 hydraulic cylinder

CK-32/22*0065-N001 hydraulic cylinder

CK-32/22*0090-P001 hydraulic cylinder

CK-32/22*0090-P001 hydraulic cylinder

CK-32/22*0100-N001 hydraulic cylinder

CK-32/22*0100-N001 hydraulic cylinder

CK-32/22*0120-N001 hydraulic cylinder CK-32/22*0120-N001 Hydraulic Cylinder

CK-32/22*0150-N001 Hydraulic Cylinder

CK-32/22*0192-C301 Hydraulic Cylinder

CK-32/22*0200-N001 Hydraulic Cylinder

CK-32/22*0220-N001 Hydraulic Cylinder CK-32/22*0220-N001 Hydraulic Cylinder

CK-32/22*0220-N001 Hydraulic Cylinder

CK-32/22*0250-N001 Hydraulic Cylinder

CK-40/18*0100-D901 Hydraulic Cylinder

CK-40/18*0120-X008 Hydraulic Cylinder

CK-40/18*0125-G908 Hydraulic Cylinder CK-40/18*0125-G908 hydraulic cylinder

CK-40/18*0125-G908 hydraulic cylinder

CK-40/18*0140-N308 hydraulic cylinder

CK-40/18*0140-N308 hydraulic cylinder

CK-40/18*0182-D901 hydraulic cylinder

CK-40/18*0182-D901 hydraulic cylinder

CK-40/18*0182-S601 hydraulic cylinder

CK-40/18*0182-S601 hydraulic cylinder

CK-40/18*0183-D601 hydraulic cylinder CK-40/18*0183-D601 cylinder CK-40/18*0183-D601

CK-125/90*0400-S301 RS

CK-125/90*0650-S301 RS

CK-125/90*1300-S301 RS

CK-160/110*0100-N701

CK-200/140*1720-S028

CK-25/12*0040-C208

CK-25/12*0040-C208 AWT

CK-25/12*100-Z308-23

CK-25/18*0050-N001

CK-25/18*0055-N001 CK-25/18*275-E308

CK-32/14*0040-N001

CK-32/14*0125-P801

CK-32/14*0140-D901

CK-125/56/56*0300-L001 Hydraulic Cylinder

CK-125/56/56*0300-L001

CK-125/90*0400-S301RS Hydraulic Cylinder

CK-125/90*0400-S301RS Hydraulic Cylinder

CK-125/90*0400-S301RS Hydraulic Cylinder

CK-125/90*0650-S301RS Hydraulic Cylinder

CK-125/90*0650-S301RS Hydraulic Cylinder

CK-125/90*0650-S301RS Hydraulic Cylinder

CK-125/90*0650-S301RS

CK-125/90*1300-S301RS Hydraulic Cylinder

CK-25/12*0040-C208 Hydraulic Cylinder

CK-25/12*0040-C208 Oil Cylinder

CK-25/12*0040-C208

CK-25/12*0040-C208 AWT Hydraulic Cylinder

Our company mainly deals in European and American brands and can source brands from any European country. For example, our advantageous German brands include: BURKERT, DEMAG, HAWE, REXROTH, HYDAC, PILZ relays, FESTO, IFM sensors, E+H, HEIDENHAIN, and P+F. Sensors: SICK (Germany), TURCK (Germany), HIRSCHMANN (Germany) industrial switches; Hengstler (Germany), MURR (Germany), SCHMERSAL (Germany), SAMSON (Germany), EPRO (Germany, Emerson subsidiary); MOOG (USA), ASCO (USA) solenoid valves, MAC (USA) solenoid valves, NUMATICS (USA), PARKER (USA) pneumatics and hydraulics, VICKERS (USA), ROSS (USA); Norgren (UK); OMAL (Italy), ATOS (Italy), CAMOZZI (Italy), UNIVER (Italy), Camozzi (Italy)