ATOS amplifier E-ME-T-01H 40/TK14AA in stock

Brand

ATOS/Italian Atos

Origin Category

Imported

Application Fields

Chemical, Petroleum, Energy, Electrical, General

ATOS Gear Pumps, ATOS Axial Piston Pumps, ATOS Vane Pumps, ATOS Hydraulic Cylinders, ATOS Relief Valves

ATOS amplifiers are devices that amplify the voltage or power of input signals. They consist of vacuum tubes or transistors, power transformers, and other electrical components. They are used in various devices such as communications, broadcasting, radar, television, and automatic control.

ATOS Amplifier Basic Introduction:

ATOS amplifiers are devices that increase the amplitude or power of signals. They are important components in signal processing tools in automation technology. The amplification effect of an amplifier is achieved by controlling the energy source with the input signal; the power consumption required for amplification is provided by the energy source. For linear amplifiers, the output is a reproduction and enhancement of the input signal. For nonlinear amplifiers, the output has a certain functional relationship with the input signal. Amplifiers are classified according to the physical quantity of the signal they process: mechanical amplifiers and electromechanical amplifiers.

ATOS amplifiers are important components of transmitting devices in communication systems. High-frequency power amplifiers are classified into two types based on their operating frequency band: narrowband and wideband. Narrowband high-frequency power amplifiers typically use a frequency-selective circuit with frequency filtering capabilities as their output circuit, hence they are also called tuned power amplifiers or resonant power amplifiers. Wideband high-frequency power amplifiers use a transmission line transformer or other wideband matching circuits as their output circuit, therefore they are also called untuned power amplifiers. A high-frequency power amplifier is an energy conversion device that converts DC energy supplied by a power source into high-frequency AC output. As known in the course "Low-Frequency Electronic Circuits," amplifiers can be classified into three classes (A, B, and C) based on their current conduction angle. Class A amplifiers have a current conduction angle of 360°, suitable for small-signal, low-power amplification. Class B amplifiers have a current conduction angle of approximately 180°; Class C amplifiers have a current conduction angle less than 180°. Both Class B and Class C are suitable for high-power operation. Class C has the highest output power and efficiency among the three operating classes. Most high-frequency power amplifiers operate in Class C. However, Class C amplifiers suffer from excessive current waveform distortion, making them unsuitable for low-frequency power amplification. They are only suitable for resonant power amplification using a tuned circuit as the load. Because the tuned circuit has filtering capabilities, the circuit current and voltage remain very close to a sinusoidal waveform, resulting in minimal distortion.

ATOS Amplifier Basic Structure:

The ATOS amplifier takes the input signal as its parameter, amplifies it, and then uses it as a bandpass filter. This signal is then combined with a reference signal and input to a multiplier. The result is then filtered by a low-pass filter before being output.

ATOS Amplifier Main Principle:

An ATOS amplifier is essentially an analog Fourier transform. The output of the lock-in amplifier is a DC voltage, proportional to the amplitude of the input signal at a specific frequency (the parameter input frequency). Other frequency components in the input signal do not contribute to the output voltage.

Two sinusoidal signals, both 1Hz and 90 degrees out of phase, multiplied together result in a sinusoidal signal with a DC bias.

Multiplying a 1Hz signal and a 1.1Hz signal results in a modulated signal with a sinusoidal profile and a DC bias of 0.

ATOS amplifier stock list:

E-ME-AC-01F 20 /A2

E-ME-AC-01F 20 /A4

E-ME-AC-01F/4R-4 20

E-ME-AC-01F/4R-4 20 /2

E-ME-AC-01F/4R-4 20 /3

E-ME-AC-01F/4R-4 20 /6

E-ME-AC-01F/I 20

E-ME-AC-01F/I 20 /2

E-ME-AC-01F/I 20 /4

E-ME-AC-01F/I 20 /6

E-ME-AC-01F/RR 20 /4

E-ME-AC-01F/RR 20 /A2

E-ME-AC-01F/RR-4 20 E-ME-AC-01F/RR-4 20 /3

E-ME-AC-01F/RR-4 20 /6

E-ME-AC-01F-4 20 /2

E-ME-AC-05F 20

E-ME-AC-05F 20 /2

E-ME-AC-05F 20 /3

E-ME-AC-05F 20 /4

E-ME-AC-05F 20 /A3

E-ME-AC-05F/4R-4 20 /3

E-ME-AC-05F/4R-4 20 /4

E-ME-AC-05F/I 20

E-ME-AC-05F/I 20 /3

E-ME-AC-05F/I 20 /4

E-ME-AC-05F/RR 20

E-ME-AC-05F/RR 20/3

E-ME-AC-05F/RR 20 /4

E-ME-AC-05F/RR-4 20 /3

E-ME-AC-05F/RR-4 20 /4

E-ME-AC-05F-4 20 /3

E-ME-AC-05F-4 20 /4

E-ME-L-01H 40/DL17SA

E-ME-L-01H 40/DL26SB

E-ME-L-01H 40/DL27SB

E-ME-L-01H 40/DL27SB

E-ME-L-01H 40/DL27SB

E-ME-L-01H 40/DL35SB

E-ME-L-01H 40/DL67SA

E-ME-L-01H 40 /LQ22SA The company mainly deals with European and American brands and can source brands from any European country. For example, our key German brands include: BURKERT, DEMAG, HAWE, REXROTH, HYDAC, PILZ relays, FESTO, IFM sensors, E+H, HEIDENHAIN, P+F sensors, SICK, TURCK, and HIRSCHMANN industrial switches. German brands: Hengstler, Murr, Schmersal, Samson, EPRO (Emerson Group)

American brands: MOOG, ASCO, MAC, NUMATICS, PARKER, Vickers, Helón (Norgren)

Italian brands: OMAL, ATOS, CAMOZZI, UNIVER, Camozzi