ATOS amplifier E-ME-L-01H 40/DL35SB in stock

Brand

ATOS/Italian Atos

Origin Category

Imported

Application Fields

Chemical, Petroleum, Mining, Road/Rail/Shipbuilding, Comprehensive

Main Uses of ATOS Amplifiers

ATOS amplifiers are mainly used to detect weak signals with very low signal-to-noise ratios. Even if the useful signal is submerged in noise, or even if the noise signal is much stronger than the useful signal, as long as the frequency of the useful signal is known, the amplitude of the signal can be accurately measured.

ATOS amplifiers are devices that amplify the voltage or power of input signals. They consist of vacuum tubes or transistors, power transformers, and other electrical components. They are used in various devices such as communications, broadcasting, radar, television, and automatic control.

Principle of ATOS Amplifiers: High-frequency power amplifiers are used in the final stage of transmitters. Their function is to amplify the high-frequency modulated wave signal to meet the transmission power requirements. Then, the signal is radiated into space through an antenna, ensuring that receivers within a certain area can receive a satisfactory signal level without interfering with communication on adjacent channels.

ATOS amplifiers are an important component of the transmitting device in a communication system. High-frequency power amplifiers are classified into two types based on their operating frequency band: narrowband and wideband. Narrowband high-frequency power amplifiers typically use a frequency-selective circuit with frequency filtering capabilities as their output circuit, hence they are also called tuned power amplifiers or resonant power amplifiers. Wideband high-frequency power amplifiers use a transmission line transformer or other wideband matching circuits as their output circuit, therefore they are also called untuned power amplifiers. A high-frequency power amplifier is an energy conversion device that converts DC energy supplied by a power source into high-frequency AC output. As known in the course "Low-Frequency Electronic Circuits," amplifiers can be classified into three classes (A, B, and C) based on their current conduction angle. Class A amplifiers have a current conduction angle of 360°, suitable for small-signal, low-power amplification. Class B amplifiers have a current conduction angle of approximately 180°; Class C amplifiers have a current conduction angle less than 180°. Both Class B and Class C are suitable for high-power operation. Class C has the highest output power and efficiency among the three operating classes. Most high-frequency power amplifiers operate in Class C. However, Class C amplifiers exhibit excessive current waveform distortion, making them unsuitable for low-frequency power amplification. They are only suitable for resonant power amplification using a tuned circuit as the load. Because the tuned circuit possesses filtering capabilities, the circuit current and voltage remain extremely close to a sinusoidal waveform, resulting in very low distortion.

E-ME-L-01H 40/DL17SA

E-ME-L-01H 40/DL26SB

E-ME-L-01H 40/DL27SB

E-ME-L-01H 40/DL27SB

E-ME-L-01H 40/DL27SB

E-ME-L-01H 40/DL35SB

E-ME-L-01H 40/DL67SA

E-ME-L-01H 40/LQ22SA

E-ME-L-01H 40/LQ32SA

E-ME-L-01H 40/DL27SB

E-ME-L-01H 40/PCNNSA

E-ME-L-01H/DL27SB

E-ME-L-01H/I 40/LQ32SA

E-ME-T-01H 40/DH04SA

E-ME-T-01H 40/DH05SA

E-ME-T-01H 40/DK14SC

E-ME-T-01H 40/DK15SB

E-ME-T-01H 40/QV0NSA

E-ME-T-01H 40/TK14AA

E-ME-T-01H 40/TK14SC

E-ME-T-01H 40/TQ25SA

E-ME-T-01H 40/TQ32SA

E-ME-T-01H 40/TQ42SA

E-ME-T-01H 40/DK14SC

E-ME-T-01H 40/DK15SB

E-ME-T-01H 40/QV1NSB

E-ME-T-01H 40/TQ25SA

E-ME-T-01H/I 40 /DH04SA

E-ME-T-01H/I 40/DK14SC

E-ME-T-01H/I 40 /DP25SB

E-ME-T-01H/I 40 /DP25SC

E-ME-T-01H/I 40 /QV0NSA

E-ME-T-01H/I 40/TQ25SA

E-ME-T-01H/I 40/DK15SB

E-ME-T-01H/I 40/QVONSA

E-ME-T-01H/I 40/TQ25SA

E-ME-T-05H 40/DH07SA

E-ME-T-05H 40/DK17SA

E-ME-T-05H 40 /DK17SB

E-ME-T-05H 40/DP27SB

E-ME-T-05H 40/DH07SA

E-ME-T-05H 40/DK17SB

E-ME-T-05H 40/DP27SB

E-ME-T-05H/I 40 /DK17SB

E-ME-T-05H/I 40/DP27SB

E-ME-T-05H/I 40/DH07SA

E-ME-T-05H/I 40/DK17SB

E-ME-T-05H/I 40/DP27SB

E-MI-AC-01F 11 /1

E-MI-AC-01F 11 /2

E-MI-AC-01F 11 /3

E-MI-AC-01F 11 /4 E-MI-AC-01F 11 /6

E-MI-AC-01F/7 11 /3

E-MI-AC-01F/7 11 /4

E-MI-AC-01F/RR 11 /1

E-MI-AC-01F/RR 11 /2

E-MI-AC-01F/RR 11 /3

E-RACK3HE21TE

E-RACK3HE28TE

E-RACK3HE42TE

E-RACK3HE49TE

E-RACK3HE56TE

E-RACK3HE84TE The company mainly deals with European and American brands and can source brands from any European country. For example, our key German brands include: BURKERT, DEMAG, HAWE, REXROTH, HYDAC, PILZ relays, FESTO, IFM sensors, E+H, HEIDENHAIN, P+F sensors, SICK, TURCK, and HIRSCHMANN industrial switches. German brands: Hengstler, Murr, Schmersal, Samson, EPRO (Emerson Group)

American brands: MOOG, ASCO, MAC, NUMATICS, PARKER, VICKERS, ROSS

British brands: Norgren

Italian brands: OMAL, ATOS, CAMOZZI, UNIVER, Camozzi