Pepperl+Fuchs (P+F) safety barrier KFD2-UFC-EX1.D in stock

Brand

P+F/Pepperl+Fuchs (Germany)

Application Areas

Environmental Protection, Biotechnology, Energy, Electrical, General

Pepperl+Fuchs P+F Sensor KFD2-UFC-EX1.D in Stock

Pepperl+Fuchs P+F Sensor Car Mixer KFD2-UFC-ex1.d

Pepperl+Fuchs P+F Safety Barrier Structure:

Zener-type Safety Barrier

The circuit uses fast-acting fuses, current-limiting resistors, or voltage-limiting diodes to limit the input electrical energy, thereby ensuring the energy output to the hazardous area is protected.

1. The installation location must have a very reliable grounding system, which is obviously very demanding and difficult to guarantee in practical engineering applications.

3. Zener-type safety barriers are significantly affected by the power supply and are easily damaged by power fluctuations.

4. Because the circuit principle of the Zener-type safety barrier requires absorbing energy from the input circuit, it is prone to output instability.

Advantages of Pepperl+Fuchs (P+F) safety barriers:

① Although isolated safety barriers are more expensive than Zener barriers, their numerous advantages and features offer significant convenience to users, leading to a growing preference for them.

② Isolated safety barriers effectively isolate field circuit signals from safe circuit signals. This eliminates the need for intrinsically safe grounding systems in intrinsically safe control systems, simplifying construction.

③ Isolated safety barriers significantly enhance the anti-interference capabilities of detection and control circuits, improving system reliability.

④ Isolated safety barriers allow for grounding of field instruments, permitting non-isolated field instruments.

⑤ Isolated safety barriers have numerous protective circuits, reducing the likelihood of accidental damage and allowing for live maintenance of field instruments, thus shortening start-up preparation time and minimizing downtime.

⑥ Isolated safety barriers possess strong signal processing capabilities, such as converting switch input status control, mV, and Pt100 to 4~20mA, etc. This provides greater convenience, rationality, and effectiveness for the application of field instruments and control systems.

⑦ When users simultaneously apply DCS and ESD, selecting a one-input, two-output safety barrier can effectively isolate the two systems, preventing mutual interference.

⑧ Loop-powered isolation safety barriers retain the advantages of active isolation safety barriers and offer the same wiring convenience as Zener barriers. They do not require a separate 24V power supply, making them particularly suitable for DCS systems directly powered by I/O cards.

Pepperl+Fuchs (P+F) safety barriers are connected between intrinsically safe and non-intrinsically safe circuits. They limit the voltage and current supplied to intrinsically safe circuits within a safe range.

Features

》Channel isolation barrier

》24V DC power supply (electric railway)

》2-wire SMART transmitter and current source input signals

》Distributor (1 input and 2 outputs)

》Dual output 0/4 mA... 20 mA or 0/1 V... 5 V

》Terminal module with test socket

》SIL 2 (SC 3) acc. 61508

Pepperl+Fuchs (P+F) Safety Barrier Introduction:

Pepperl+Fuchs (P+F) safety barriers, also known as safety limiters, are an important component of intrinsically safe systems.

Pepperl+Fuchs (P+F) safety barriers are mainly divided into two categories: Zener barrier type and isolation barrier type.

The core components of a Zener barrier are a Zener diode, a current-limiting resistor, and a fast-blow fuse.

Isolation barriers not only limit energy but also provide isolation. They mainly consist of a loop limiting unit, a signal and power isolation unit, and a signal processing unit.

The primary function of a safety barrier is to limit current and voltage, ensuring that the energy available to field instruments remains within safe limits.

The following are Pepperl+Fuchs (P+F) safety barriers in stock:

KCD2-STC-Ex1

KCD2-SCD-EX1

KCD2-STC-1

KCD2-SCD-1

KFD2-STC5-EX1

KFD2-STC5-EX1.2O

KCD2-STC-EX1.20

KCD2-STC-1.2O

KFD2-STC5-1.2O

KCD2-UT2-EX1

KFD2-UT2-EX2

KFD2-UT2-EX1

KFD2-STC5-EX2

KFD2-CD-EX1.32

KFD2-EB2.R4A.B

KFD0-SD2-EX1.1045

KCD0-SD-EX1.1245

KFD2-VR4-EX1.26

KCD2-RR-EX1 KFD2-SCD-EX1.LK

KFD2-SCD2-Ex2.LK

KFD2-SCD2-EX1.LK

KCD2-SR-EX1.LB

KCD2-SOT-EX1.LB

KFD2-SR2-EX1.W

KFD2-SR2-EX2.W

KFD2-SR2-EX1.W.LB

KFA6-SR2-EX1.W

KFD2-STC5-1

KFD2-SOT3-EX2

KCD2-STC-1.20

UPR-03

KFD0-RSH-1

K-ADP-USB

KFD2-UT2-1

KFD2-CRG2-Ex1.D

KFD2-UFC-EX1.D

KCD2-SR-EX2

KCD2-UT2-1

KCD2-SOT-EX2

FS-LB-I KFA6-SR2-EX2.W

KFD2-DWB-EX1.D

KFD2-SL2-EX2.B

KFD2-UT2-EX2-1

KCD2-STC-EX1.ES

KFD0-RSH-1.4S.PS2

KFU8-UFC-1.D

KFD2-STC4-EX1.2O

Our company mainly deals in European and American brands and can purchase brands from any European country. For example, our advantageous German brands include: BURKERT, DEMAG, HAWE, REXROTH, HYDAC, PILZ relays, FESTO, IFM sensors, E+H, HEIDENHAIN, P+F sensors, SICK, TURCK, and HIRSCHMANN industrial switches. German brands: Hengstler, Murr, Schmersal, Samson, EPRO (Emerson's subsidiary), MOOG (USA), ASCO (USA), MAC (USA), NUMATICS (USA), PARKER (USA), VICKERS (USA), ROSS (USA), Norgren (UK), OMAL (Italy), ATOS (Italy), CAMOZZI (Italy), UNIVER (Italy), and Camozzi (Italy).