Dynisco pressure sensor PT4604-3M-12-SIL2 available now.

Brand

Dynisco/American Dynisco

Application Areas

Medical and Health, Environmental Protection, Food/Agricultural Products, Chemical Industry, Petroleum

Characteristics of American Dynisco Pressure Sensors:

American Dynisco sensors have high resistance to vibration, shock, and electromagnetic interference, requiring very strict overpressure capability. They also have a reliable mechanical seal to prevent loosening. The sensor must be correctly installed. The guide pins and wires should be electromagnetically shielded, grounded, and well-shielded. Furthermore, the compatibility of the measured fluid pressure medium should be considered.

Correct Installation Method for American Dynisco Pressure Sensors:

(1) Using appropriate instruments, at standard temperature and pressure, query the frequency response value of the pressure sensor under normal conditions.

Code and corresponding frequency.

(2) Verify the correctness of the pressure sensor's response signal.

2. Determine the Specific Installation Location

Determine the specific number of pressure sensors and the installation location for each inflation section of the AC network.

(1) The pressure sensor must be installed along the cable, preferably at the cable connector. Dynisco Pressure Sensor Installation Guidelines (USA):

1. If two branch points are close (less than 100 meters), only one can be installed.

2. Each pressure sensor cable should be installed within four years of its installation. For two pressure sensors near a telephone exchange, the distance should not exceed 200 meters.

3. A start and end of each cable should be installed.

4. Each cable branch point should be installed.

5. Changes in cable laying method (above and underground) should be considered during installation.

6. No branch cables are allowed, as the bottom line of the cable scheme should be the installation length of the pressure gauge sensor within 500 meters, and four total...

Dynisco Parameters:

When at a certain temperature (23°C), the Dynisco pressure sensor's high-temperature melt changes the value of the pressure, increasing or decreasing the pressure. The pressure value obtained at the operating point is adjusted to eliminate the full-scale value of the output pressure.

The nominal pressure value is predetermined to meet standard pressure requirements. That is, between the highest and lowest temperatures, the load cell's output characteristics conform to the working pressure. The Dynisco sensor measures pressure within a certain range in practical applications. Sensitivity (mV/V) 1.0±0.05 Sensitivity Temperature Coefficient ≤%F·S/10℃±0.03

Nonlinearity ≤%F·S±0.02±0.03 -1140-75kg Operating Temperature Range (℃) -20℃+80℃

Hysteresis ≤%F·S±0.02±0.03 Input Impedance (Ω) 400±10Ω

Repeatability ≤%F·S±0.02±0.03 Output Resistance (Ω) 350±5Ω

Creep ≤%F·S/30min±0.02 Safe Overload ≤%F·S 150%F·S

Zero-Point Output ≤%F·S±2 Insulation Resistance (MΩ) ≥5000MΩ (50VDC)

Zero Temperature Coefficient ≤%F·S/10℃±0.03 Recommended Excitation Voltage (V) 10V-15V

Temperature Range: The temperature range of Dynisco pressure sensors from the USA is divided into a compensated temperature range and a standard operating temperature range. Temperature compensation ensures accuracy within the rated temperature range. The standard operating temperature range guarantees normal operation of the pressure sensor.

Dynisco Pressure Sensors

1. PT460E Standard Type, Rigid Rod Melt Pressure Sensor

The PT460E pressure sensor is a standard type in the polymerization industry. This model is a general-purpose melt pressure measurement sensor, easy to install, and offers good accuracy, repeatability, and reliability.

Features:

1. Accuracy better than ±0.5%FS

2. 3.33 mV/V full-scale output

3. Internal 80% calibration

4. Stainless steel construction

5. Pressure range from 0 - 500 PSI to 0 - 30,000 PSI

6. Good stability and repeatability

7. CE certified

2. PT462E Standard Type, Melt Pressure Sensor with Flexible Tube

The PT462E features an 18" flexible tube between the rigid tube and the strain gauge housing, increasing thermal isolation. It offers good repeatability and accuracy at an economical price. It is widely used globally by OEMs.

Features:

1. Accuracy better than ±0.5%FS

2. 3.33 mV/V full-scale output

3. Internal 80% calibration

4. Stainless steel construction

5. Pressure range from 0 - 500 PSI to 0 - 30,000 PSI

6. 7. CE Certification

3. PT463E Standard Type with Thermocouple: The TPT463E fusion pressure sensor integrates the PT462E with a detachable J-type thermocouple, allowing simultaneous measurement of pressure and temperature at the same point. It also features a flexible tube for easy installation.

Features:

1. Accuracy better than ±0.5%

2. Measures pressure and temperature at the same point

3. Standard detachable J-type thermocouple

4. 3.33 mV/V full-scale output

5. Internal 80% calibration

6. Pressure range from 0 - 500 psi to 0 - 30,000 psi

7. CE Certification with Flexible Tube

8. RTD and other thermocouples optional

Pressure Sensor Accessories: Fusion Pressure Gauge Sensor PT4604-3M-12-SIL2

Pressure Sensor Accessories: Fusion Pressure Gauge Sensor PT4604-1.5M-12-SIL2

Pressure sensor accessories, melt pressure gauge, sensor PT4604-3M-12-A

Pressure sensor accessories, melt pressure gauge, sensor PT4604-1.5M-12-A

DYNA-4-1M-15 is an older model; the upgraded model is now PT460E-1M-6.

Dynisco products include: Dynisco melt pressure sensors, Dynisco online rheometers, Dynisco capillary rheometers, Dynisco melt indexers, Dynisco humidity analyzers, Dynisco HDT/VICAT heat distortion and Vicat softening point temperature measuring instruments, Dynisco LMI 4000 melt indexers, Dynisco-1390 display instruments, Dynisco NYN-X series melt pressure sensors, Dynisco MRT460 rod-type melt pressure sensors, Dynisco EPR 4 series push-rod pressure transmitters, and Dynisco... IPX II 2192 Series Smart Pressure Transmitter, Dynisco TCS, TCE Temperature Controller, Dynisco TX190 Rail-Mounted Temperature Transmitter, Dynisco TI422J Adjustable Thermocouple, Dynisco TG422J Thermocouple for Extruder Measurement, Dynisco TB422J Temperature Sensor for Extrusion Barrel, Dynisco IPX II 1194 Smart Pressure Transmitter - Flange Mount, Dynisco IPX II 2195 Smart Pressure Transmitter, Dynisco EPR5 & EPR6 Push-Rod Pressure Transmitter, Dynisco EPR5-TC, EPR6-TC Push-Rod Melt Pressure Transmitter, Dynisco PT4675, PT4676, Pressure for Confined Spaces, Dynisco Dynipaks Pressure Display and Control Kit, Dynisco RMM, FMM Pressure Transmitter with Display, Dynisco RMM, FMMX Pressure Transmitter with Monitoring Function, Dynisco PT415D food extrusion pressure sensor, Dynisco PT467E pressure sensor for confined spaces, Dynisco PT460XL wear-resistant melt pressure sensor.

Our company mainly deals in European and American brands and can source brands from any European country. For example, our key German brands include: BURKERT, DEMAG, HAWE, REXROTH, HYDAC, PILZ relays, FESTO, IFM sensors, E+H, HEIDENHAIN, P+F sensors, SICK, TURCK, HIRSCHMANN industrial switches, Henschler, MURR, SCHMERSAL, SAMSON, and EPRO (a subsidiary of Emerson). MOOG (USA), ASCO (USA), MAC (USA), NUMATICS (USA), PARKER (USA), VICKERS (USA), ROSS (USA)

Norgren (UK)

OMAL (Italy), ATOS (Italy), CAMOZZI (Italy), UNIVER (Italy), Camozzi (Italy)