ATOS proportional directional valve DKZOR-A-173-D5 in stock

Brand

ATOS/Italian Atos

ATOS proportional directional valves from Italy control flow in two ways: One is on/off control: either fully open or fully closed, with flow either at its maximum or minimum, without intermediate states, such as ordinary solenoid direct-flow valves, solenoid directional valves, and electro-hydraulic directional valves. The other is continuous control: the valve port can open to any degree as needed, thereby controlling the flow rate. These valves can be manually controlled, such as throttle valves, or electrically controlled, such as proportional valves and servo valves. Therefore, the purpose of using proportional or servo valves is to achieve throttling control of flow rate electronically (of course, pressure control can also be achieved through structural modifications). Since it is throttling control, there is inevitably energy loss. Servo valves differ from other valves in that their energy loss is greater because they require a certain flow rate to maintain the operation of the upstream control circuit.

The structural principle of the ATOS proportional valve:

When the input signal to the ATOS proportional valve increases, the pilot valve 1 of the supply solenoid valve switches, while the exhaust solenoid pilot valve 7 remains in the reset state. The supply pressure then enters the pilot chamber 5 through the SUP port and valve 1. The pressure in the pilot chamber rises, and this pressure acts on the diaphragm 2, opening the supply valve core 4 connected to diaphragm 2 and closing the exhaust valve core 3, generating output pressure. This output pressure is fed back to the control loop 8 via pressure sensor 6. Here, a rapid comparison and correction is performed with the target value until the output pressure is proportional to the input signal, thus demonstrating that the output pressure changes proportionally to the change in the input signal. Because there is no nozzle-baffle mechanism, the valve is insensitive to impurities and has high reliability.

Features of the ATOS proportional valve:

1) It can achieve stepless adjustment of pressure and speed, avoiding the impact phenomenon during switching of normally open on/off valves.

2) It can achieve remote control and program control.

3) Compared with intermittent control, the system is simplified, and the number of components is greatly reduced. 4) Compared to hydraulic proportional valves, it is smaller, lighter, simpler in structure, and lower in cost, but its response speed is much slower than hydraulic systems, and it is more sensitive to load changes.

5) It uses less power, generates less heat, and has lower noise.

6) It will not cause fires and will not pollute the environment. It is less affected by temperature changes.

The performance of the Italian ATOS proportional directional valve is between that of a servo valve and a proportional valve.

Proportional directional valves are a type of proportional valve used to control flow rate and direction.

Extended Information---Automatic control of electric proportional valves can be divided into intermittent control and continuous control. Intermittent control is on/off control. Pneumatic control systems use on/off directional valves with low operating frequency to control the opening and closing of the air path. Pressure reducing valves are used to regulate the required pressure, and throttle valves are used to regulate the required flow rate. This traditional pneumatic control system requires multiple pressure reducing valves, throttle valves, and directional valves to achieve multiple output forces and multiple movement speeds. This not only requires more components, increases cost, and complicates the system, but also requires many components to be manually adjusted in advance. Electro-proportional valve control is a type of continuous control, characterized by an output that changes proportionally to the input, with a certain proportional relationship between the two. Proportional control can be divided into open-loop control and closed-loop control.

DHZO-AT-073-P3 20

DHZO-ATE-073-P3/B/DP27SB 20

DHZO-T-051-L1

DHZO-T-051-L5 31

DHZO-T-071-D5

DHZO-T-071-L5

DHZO-T-071-S5

DHZO-TE-051-L5/Y 40

DHZO-TE-071-L5

DHZO-TE-071-S5 40/PE

DHZO-TE-073-S5

DKZA-A-173-L5/PA-M/7

DKZO-A-151-S5

DKZO-A-171-L5

DKZO-A-173-S5 DKZOR-A-151-S5

DKZOR-A-151-S5/18 40

DKZOR-A-151-S5/B

DKZOR-A-153-L5/B

DKZOR-A-171-D5 40

DKZOR-A-171-L5

DKZOR-A-171-S5

DKZOR-A-171-S5/18

DKZOR-A-173-D5

DKZOR-A-173-L5

DKZOR-A-173-L5/18 40

DKZOR-A-173-L5/Y

DKZOR-A-173-S3

DKZOR-A-173-S5

DKZOR-A-173-S5/18 DKZOR-AE-171-L5 10

DKZOR-AE-171-S5

Our company mainly deals in European and American brands and can source brands from any European country. For example, our advantageous German brands include: BURKERT, DEMAG, HAWE, REXROTH, HYDAC, PILZ relays, FESTO, IFM sensors, E+H, HEIDENHAIN, P+F sensors, SICK, TURCK, and HIRSCHMANN industrial switches. German brands: Hengstler, Murr, Schmersal, Samson, EPRO (Emerson Group)

American brands: MOOG, ASCO, MAC, NUMATICS, PARKER, VICKERS, ROSS

British brands: Norgren

Italian brands: OMAL, ATOS, CAMOZZI, UNIVER, Camozzi